| |
 |
 |
Choice of paper
cutting machine |
 |
 |
Inquiries
Inquiries are welcome. Contact us
by phone, by fax,
or by e-mail.
|
 |
|
 |
 |
 |
 |
 |
 |
 |
 |
Wood
Wood paper for laminated plywood |
Wood
The material is cork |
Felt
Honeycomb |
Paper and
paper craft
Paper |
Paper and
paper craft
Packing |
Paper and
paper craft
Twisted paper string ornament |
Paper and
paper craft
Hard press board |
 |
 |
 |
 |
 |
 |
|
Felt
Wool felt |
Felt
Saran rack filter |
Felt
Cloth felt |
Plastic
Plastic cardboard |
Plastic
Polyester film |
Plastic
Paulownia |
|
 |
 |
 |
 |
 |
 |
 |
Urethane
Urethane resin |
Urethane
Urethane foam |
Rubber
Rubber |
Vinyl
Soft vinyl sheet |
Glass fiber
Glass fiber mat |
Metal
Metal deposition sheet |
PS board
PS board mat |
|
 |
|
Workpiece (material to be cut)：Felt, non-woven fabric, filter |
 |
|
 |
Cutting case, company G
| Material to be cut： |
Wool felt (18mm thick), air filter, brush material, non-woven fabric |
| Cutting machine： |
eRC-137DX |
|
【Key points of cutting】
| Material and angle of cutting edge |
High-speed steel 21-23° |
| Setting method |
Same as paper. A roll-shaped material should be processed in a flat shape in advance and loaded from the front, or the roll should be set at the rear of the leveling block and drawn toward the front to cut. |
| Clamp (pressing method) |
Gently press |
| Pressure |
4KN |
| Angle at which the cutting edge is lowered |
Standard |
| Method of clamping the cut material |
Immediate release |
| Others |
|
|
|
|
|
Workpiece (material to be cut)：Felt, needle |
|
 |
Cutting case, company H
| Material to be cut： |
Felt, max. 20mm thick |
| Cutting machine： |
JAC－160CFC |
|
【Key points of cutting】
| Material and angle of cutting edge |
High-speed steel 21-23° |
| Setting method |
Same as paper. A roll-shaped material should be processed in a flat shape in advance and loaded from the front, or the roll should be set at the rear of the leveling block and drawn toward the front to cut. |
| Clamp (pressing method) |
Gently press |
| Pressure |
8KN high/low switching provided, 2KN in case of low pressure. |
| Angle at which the cutting edge is lowered |
Standard |
| Method of clamping the cut material |
Immediate release |
| Others |
|
|
|
|
Workpiece (material to be cut)：Vinyl, non-woven fabric |
|
 |
Cutting case, company R
| Material to be cut： |
Non-woven fabric |
| Cutting machine： |
JAC-160NFC |
|
【Key points of cutting】
| Material and angle of cutting edge |
High-speed steel 23° |
| Setting method |
Because the material is large, connect an auxiliary table in front of the leveling block to feed. |
| Clamp (pressing method) |
The clamp pedal is not used. |
| Pressure |
6KN |
| Angle at which the cutting edge is lowered |
Standard |
| Method of clamping the cut material |
Immediate release |
| Others |
Low knife speed control with inverter |
|
|
|
Low knife speed control with inverter |
|
 |
Cutting case, company V
| Material to be cut： |
saran rack filter Filter element used for filter, etc. |
| Cutting machine： |
eRC-137DX |
|
【Key points of cutting】
| Material and angle of cutting edge |
High-speed steel 21-23° |
| Setting method |
Same as paper. A roll-shaped material should be processed in a flat shape in advance and loaded from the front, or the roll should be set at the rear of the leveling block and drawn toward the front to cut. |
| Clamp (pressing method) |
block and drawn toward the front to cut. |
| Pressure |
4KN |
| Angle at which the cutting edge is lowered |
Standard |
| Method of clamping the cut material |
Immediate release |
| Others |
|
|
|
|
|
|
